Differences

This shows you the differences between two versions of the page.

--- simple_rotator_interface_v [2025/02/16 16:40] – [KENPRO KR-1000] ok1hra
+++ simple_rotator_interface_v [2025/02/19 02:24] (current) – ok1hra
@@ Line 1: / Line 1: @@
 ====== Simple Rotator Interface V. assembled version (release 2024) ======
@@ Line 152: / Line 153: @@
 {{https://remoteqth.com/img/wiki-simple-rot-75.png?800}}
-==== KENPRO KR-1000 ====
-Simple Rotator Interface V. is used **as a replacement for the original control unit with its own DC power supply** for the rotator motor. \\ **Terminal connection** according to the picture (above). \\ More about [[#dc_motor_with_pwm|DC motor with PWM]]. \\
+==== hy-gain HAM IV ====
+Simple Rotator Interface V. is used **as a replacement for the original control unit with its own AC power supply** for the rotator motor. \\ **Terminal connection** according to the picture (above). \\ More about [[#ac_motor|AC motor]] connetions. \\
 | **Setup** Web page basic settings - [[#setup_web_page|more]]  |
-| Azimuth potentiometer | 3 Wire |
+| Azimuth potentiometer | 2 Wire |
 | Azimuth gain/shift op-amp | OFF |
 | Hardware endstops | INSTALLED: ☑ |
-| Motor supply | DC |
+| Motor supply | AC |
+**ATTENTION - the POE injector must be powered from another source than the source for AC motor!**
-{{https://remoteqth.com/img/wiki-simple-rot-KENPRO-KR-1000.png?800}}
+{{https://remoteqth.com/img/wiki-simple-rot-hy-gain-HAM-IV.png?800}}
 ----
-==== hy-gain HAM IV ====
+==== KENPRO KR-1000 ====
-Simple Rotator Interface V. is used **as a replacement for the original control unit with its own AC power supply** for the rotator motor. \\ **Terminal connection** according to the picture (above). \\ More about [[#ac_motor|AC motor]] connetions. \\
+Simple Rotator Interface V. is used **as a replacement for the original control unit with its own DC power supply** for the rotator motor. \\ **Terminal connection** according to the picture (above). \\ More about [[#dc_motor_with_pwm|DC motor with PWM]]. \\
 | **Setup** Web page basic settings - [[#setup_web_page|more]]  |
-| Azimuth potentiometer | 2 Wire |
+| Azimuth potentiometer | 3 Wire |
 | Azimuth gain/shift op-amp | OFF |
 | Hardware endstops | INSTALLED: ☑ |
-| Motor supply | AC |
+| Motor supply | DC |
-{{https://remoteqth.com/img/wiki-simple-rot-hy-gain-HAM-IV.png?800}}
+{{https://remoteqth.com/img/wiki-simple-rot-KENPRO-KR-1000.png?800}}
 ----
@@ Line 266: / Line 269: @@
 **Open the IP address** found using the previous instruction **in a web browser** http://[YOUR-IP] \\ {{https://remoteqth.com/img/wiki-simple-rot-08.png?400}} \\ How to works
     - The first page contains an **information header,** including a link to the **Firmware Upload** page and the **Release page** on GitHub. Give **green the button of the link to the control page** of the rotator. Below it is the **web MQTT client** (credit [[https://github.com/bastlirna/mqtt-wall|MQTT wall]]) displaying the data sent or received by the rotator from the MQTT broker - data used to **control or debug** the rotator.
+    - This client requests an MQTT instance running on **web socket port 1884**.
 ----