Differences

This shows you the differences between two versions of the page.

--- simple_rotator_interface_v [2025/02/16 17:17] – [hy-gain HAM IV] ok1hra
+++ simple_rotator_interface_v [2026/02/13 21:13] (current) – ok1hra
@@ Line 3: / Line 3: @@
 Web interface with MQTT an USB support
   * [[https://remoteqth.com/single-rotator-interface.php|Web page]]
-  * **[[https://remoteqth.com/order.php#rotator-interface|Order]]**
+  * **BUY on ** [[https://hamparts.shop/simply-rotator-controller-with-web-interface.html|hamparts.shop]]
   * [[https://remoteqth.com/w/doku.php?id=simple_rotator_interface_v_kit|KIT version V.]] (release 2023)
   * [[https://remoteqth.com/w/doku.php?id=usb_rotator_interface_4|Previous of version 4]]
@@ Line 152: / Line 152: @@
 {{https://remoteqth.com/img/wiki-simple-rot-75.png?800}}
+==== YAESU G800SA / G1000SA ====
+Simple Rotator Interface V. is used **as a replacement for the original control unit with its own DC power supply** for the rotator motor. \\ **Terminal connection** according to the picture (above). \\ More about [[#dc_motor_with_pwm|DC motor with PWM]]. \\
+| **Setup** Web page basic settings - [[#setup_web_page|more]]  |
+| Azimuth potentiometer | 3 Wire |
+| Azimuth gain/shift op-amp | OFF |
+| Hardware endstops | INSTALLED: ☑ |
+| Motor supply | DC |
+{{https://remoteqth.com/img/wiki-simple-rot-G800SA-G1000SA.png?800}}
+----
 ==== hy-gain HAM IV ====
@@ Line 160: / Line 171: @@
 | Hardware endstops | INSTALLED: ☑ |
 | Motor supply | AC |
-**ATTENTION - the POE injector must be powered from another source than the source fo AC motor!**
+**ATTENTION - the POE injector must be powered from another source than the source for AC motor!**
 {{https://remoteqth.com/img/wiki-simple-rot-hy-gain-HAM-IV.png?800}}
@@ Line 166: / Line 177: @@
 ----
-==== KENPRO KR-1000 ====
+==== KENPRO KR-1000 / YAESU G800-G1000 ====
 Simple Rotator Interface V. is used **as a replacement for the original control unit with its own DC power supply** for the rotator motor. \\ **Terminal connection** according to the picture (above). \\ More about [[#dc_motor_with_pwm|DC motor with PWM]]. \\
 | **Setup** Web page basic settings - [[#setup_web_page|more]]  |
@@ Line 268: / Line 279: @@
 **Open the IP address** found using the previous instruction **in a web browser** http://[YOUR-IP] \\ {{https://remoteqth.com/img/wiki-simple-rot-08.png?400}} \\ How to works
     - The first page contains an **information header,** including a link to the **Firmware Upload** page and the **Release page** on GitHub. Give **green the button of the link to the control page** of the rotator. Below it is the **web MQTT client** (credit [[https://github.com/bastlirna/mqtt-wall|MQTT wall]]) displaying the data sent or received by the rotator from the MQTT broker - data used to **control or debug** the rotator.
+    - This client requests an MQTT instance running on **web socket port 1884**.
 ----