double_sun_shield_for_thermometer
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| double_sun_shield_for_thermometer [2023/09/08 08:44] – [BOM] ok1hra | double_sun_shield_for_thermometer [2024/01/09 21:53] (current) – [3D print Double sun shield for thermometer DS18B20] ok1hra | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== 3D print Double sun shield for thermometer DS18B20 ====== | ====== 3D print Double sun shield for thermometer DS18B20 ====== | ||
| - | 3D printed shield, against overheating of the thermometer in direct sunlight. | + | {{ https:// |
| + | 3D printed shield, against overheating of the thermometer in direct sunlight. | ||
| + | **The doubling of the shield makes it possible to better shield the salve heat from the heated outer shield.** | ||
| + | **[[https:// | ||
| + | **[[https:// | ||
| + | * I include the source file **sun-shield.scad** in OpenScad | ||
| + | * **exported .STL** files for individual parts (preset for mounting rods with a diameter of 42 mm) | ||
| + | * **preset .3mf** files | ||
| - | [[https:// | + | ---- |
| - | Source files on GitHub | + | |
| - | * I include the source file sun-shield.scad in OpenScad | + | |
| - | * exported .STL files for individual parts (preset for mounting rods with a diameter of 42 mm) | + | |
| - | * preset .3mf files | + | |
| - | \\ | + | |
| - | Printed parts \\ {{https:// | + | |
| ===== BOM ===== | ===== BOM ===== | ||
| - | | {{https:// | + | |
| + | You can use **3D printing to order,** for example at **[[https:// | ||
| + | | {{https:// | ||
| | {{https:// | | {{https:// | ||
| | {{https:// | | {{https:// | ||
| Line 20: | Line 23: | ||
| ===== Tools ===== | ===== Tools ===== | ||
| | {{https:// | | {{https:// | ||
| + | | | Soldering station | | ||
| ---- | ---- | ||
| Line 41: | Line 45: | ||
| - Screw together all four 3d printed parts number 4, using twelve M3 screws \\ {{https:// | - Screw together all four 3d printed parts number 4, using twelve M3 screws \\ {{https:// | ||
| - Finally, close by screwing the 3D printed part number 5 \\ {{https:// | - Finally, close by screwing the 3D printed part number 5 \\ {{https:// | ||
| - | - Attach the assembled shield to the mounting pipe using two plastic binding strips \\ {{https:// | + | - Attach the assembled shield to the mounting pipe using two plastic binding strips \\ {{https:// |
| + | |||
| + | |||
| + | ---- | ||
| + | |||
| + | |||
| + | ===== Connected to a 3D print weather station ===== | ||
| + | [[3D print WX station]] Wiki | ||
| + | |||
| + | - Unscrew the brass nut, remove the grille and unscrew the second brass nut below it. \\ {{https:// | ||
| + | - Remove the printed part number 2 from the weather station and pass the cable from the thermistor through the grille and the removed part. Putting on the grid during stretching will make it easier for you to orientate it. Pay attention to the direction of the cable, soldered ends inwards/ | ||
| + | - Solder the end of the cable to the PCB as shown in the picture \\ {{https:// | ||
| + | - Put the plastic parts back on the weather station and screw with the brass nut. \\ {{https:// | ||
| + | - Put the grill back on, screw it with a brass nut and fasten the free cable to the threaded rod with a plastic tie. \\ {{https:// | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| - | ===== Connected to a 3D printed weather station ===== | ||
| - | - some \\ {{https:// | ||
| - | - some \\ {{https:// | ||
| - | - some \\ {{https:// | ||
| - | - some \\ {{https:// | ||
| - | - some \\ {{https:// | ||
| - | - some \\ {{https:// | ||
| - | - some \\ {{https:// | ||
double_sun_shield_for_thermometer.1694162650.txt.gz · Last modified: 2023/09/08 08:44 by ok1hra