Easy Controller 6-2 for six-2-two antenna switch with remote control
This is universal manual, automatic (OTRSP) and remote (web, IP, cluster) controller for any antenna 6 to 2 switch. There is universal output driver - you can use +12 V OUT or switching to the Ground. Outputs could be classic 2x6 wires or BCD output 2x3. There is also WiFi client inside. You are able to control switching by the web-based User Interface (UI). Controller have got built-in PTT hot switch protection, PTT OUT break when no antenna selected and lock between antennas - first win.
Main functions:
- Universal controller for any 6-to-2 switch
- Press buttons with LED
- WEB-based control over the WiFi
- OTRSP over protected USB port SO2R protocol (N1MM, Wintest etc)
- Antenna switching protection between TRX A nd B
- HOT switch PTT protection
- PTT OUT (PA) protection
- All outputs are universal +12V or GND (depends on installed driver)
- Output 2x6 or BCD
- All three ways of the control could work together (buttons, web, OTRSP)
WEB remote control:
- Web based application with automated updates
- No configuration or firmware upload needed
- Custom button labels by parameter
- Customize your UI or use our control view
- Can be controlled by stream deck, touchportal and NodeRed
- System is part of our station automation infrastructure by DM5XX's RemoteSwitch.de system
- Remote Control follows front panel buttons
- PTT info for both TRX + switching protection
- We recommend a VPN while using remote access from outside your network in general
USB control:
- USB control based on OTRSP protocol
- Logging software configuration for OTRSP needed manual
- Automatic port switching by the logging SW.
- Manual and web-based control still works
- Logging software could only switch ports, can not read status from controller
- Tested with N1MM+, WinTest, DXlog
Parameters:
- DC supply voltage 13,8 V DC plug
- DC current supply max. 1,5 A
- DC EXTernal supply max. 26 V (pin Vext + only for relay output)
- DC EXTernal current max. 1 A (pin Vext + only for relay output)
- Output is universal +13,8 V or + EXT or to GND - (TBD driver) (ULN driver)
- Outpus 2x6 or BCD picture
- BCD output is DC supply voltage or Vext one (could be TTL 5 V)
- BCD output TTL when Vext = 5 V, jumper to Vext
- Output current max. 500mA per output, 500mA total / bank
- Voltage drop for TBD driver typ. 0,2V for +13,8 V input and 0,7V including fuse
- Voltage drop for ULN driver typ. 0,8V for +13,8 V input
- RFI filtered USB port, compatible with OTRSP protocol
- WiFi 2,4 GHz CLIENT with external antenna (SMA at rear panel)
- WiFi 2,4 GHz b/g/n compatible
- Web-based remote control picture
- WiFi SSID and password configuration by the WEB page picture
- PTT hot switch protection PTT (TX = GND)
- TRX A-B lock (first win) can not set the same antenna
- USED LED and PTT IN/OUT protection while NO ANT or locked one manual
Included in package:
- Controller assembled and tested
- DC plug cable connection
- USB cable
- WiFi omni directional antenna 6 dBi
- DB15 male connector with cover
Front panel
Example of remote control User Interface (UI) with open configuration
Connectors:
Related products:
6-to-2 ANT switch classic MK2 - BCD |
6-to-2 ANT switch triplexer MK2 - BCD |
Easy Controller 4-1 |
||
Easy Controller 6-1 |
Easy Controller for 1-2 stack match |
Controller for 1-3 stack match |